Denali 2.0 D4 TriOptic LED Light Kit with DataDim Technology

This vehicle specific split horn mount allows you to mount the DENALI SoundBomb Split Dual-Tone Air Horn in the optimum location on your BMW R 1250 GS/GSA. This kit includes one powder-coated steel bracket to mount the horn compressor behind the cylinder head and a second bracket to mount the horn acoustic unit centered under the fairing stay.   This split horn mount (DENHMT.07.11001) was recently redesigned to replace our original horn mount (DENHMT.07.10700) to ensure that the horn components can only be installed in one specific orientation eliminating the possibility of installing them incorrectly and maximizing suspension clearance. The two M8 mounting points and indexing tab on the acoustic unit bracket ensure that the horn can not rotate once installed.

DENALI Slip-On Blackout Covers keep your bike street legal in states that require aftermarket lighting to be covered on public roads. Once you get to the trails, slip the covers off of your DENALI D4 lights and go. The rugged silicone construction of the Slip-On Covers protects from rocks and other debris, providing an even longer lifespan to your DENALI D4 lights.

This Denali Mount Kits allow you to mount any Denali lights on your BMW R 1250 GS Adventure 2019- with ease, the laser-cut mild steel powder coated black bracket is both strong and attractive. This kit allows fitment of any Denali LED Lights.What's in the Box: Denali Lighting LED mounting bracket Installation instructions Mounting HardwarePlease Note: No lights are included with this kit, Mounting Bracket ONLY. Denali Lights available separately.

This Denali Mount Kits allow you to mount any Denali lights on your BMW F850 GS / F750 GS 2018- with ease, the laser-cut mild steel powder coated black bracket is both strong and attractive.Please Note: No lights are included with this kit, Mounting Bracket ONLY. Denali Lights available separately.

Denali Crashbar Light Mounts (Fits crashbars 32mm-38mm in diameter) These stylish clamps are machined from 6061-T6 Aluminum for strength and durability. The kit allows fitment of any Denali LED Lighting Kit to any tubular bar ranging from 32mm to 38mm in diameter. The bracket can be mounted in numerous positions allowing the light pods to be placed for optimal beam projection, while keeping the pods themselves protected.Kit Includes: 2x anodized aluminum machined clamp Mounting HardwareCompatible with ALL Denali lights.

This DENALI Fork Tube Light Mount Kit allows fitment of any DENALI LED Light Kit to conventional forks, or any tube 39mm - 49mm (1.5" - 1.875") in diameter. These light mounts have a unique octagonal inner profile that allow the clamps to securely grip a wide range of tube diameters and include an optional, fully rotatable mounting shelf to create a super versatile and robust light mounting solution. Available in either Black or Chrome finish. Features: Adjustable grip range 39mm - 49mm Rotatable Mounting Shelf allows 4th axis of adjustability Lights can be mounted to shelf or directly to the clamp itself Accepts M8 bolt from light pods Billet aluminum anodized in black Included: (2) Mounting clamps (2) Rotatable mounting shelves Assembly hardware Installation instructions

2.0 CANsmart Plug-N-Play Controller For BMW K1600 Series, F750GS & F850GS(A) '19-. S1000XR '15-'19, F900XR '20- E-Mark Approval Number: E11*10R05/01*10262*00 We didn't want to make just another accessory controller, we wanted to make a smarter one. Harness the power and intelligence of your vehicle's CANbus electrical system. The DENALI CANsmart Controller provides plug-n-play installation of up to four accessories to enable dozens of customizable settings that can be controlled right from the BMW "WonderWheel" or the CANsmart Accessory Manager Software. The four dedicated circuits are pre-programmed to connect and independently control two sets of auxiliary lights, an auxiliary horn, and an auxiliary brake light. Each accessory circuit is electronically fused and ready to rock right out of the box. The two auxiliary light circuits enable independent adjustment of high and low beam brightness right from the vehicles "WonderWheel". It also features a "flash to pass" and "strobe when horn active" setting that will strobe the auxiliary lights when you pulse your high beam switch or sound your horn. The feature-rich brake light circuit will transform a simple 2-wire brake light into a "smart brake light" complete with running light, multiple flash pattern, and deceleration activated braking functionality. The horn circuit enables the addition of an auxiliary horn without having to add a relay and dedicated horn wiring harness. Simple Circuit Over-Ride Want more flexibility; we thought you might. You can set any of the four circuits to "Simple Circuit" Mode which will disable all custom circuit settings to provide a clean switched 12V circuit to power an accessory of your choice. Use this setting to power an alternative accessory in place of the dedicated DENALI accessory. The electronic fuse is the only active setting so you can properly fuse your accessory.

2.0 CANsmart Plug-N-Play Controller for BMW R1200GS(A) LC/RT '14-'18; R1200RS/R '15-'18; R1200GSA '19-; R1250GS/RT/GSA/R/RS '19- GEN2. E-Mark Approval Number: E11*10R05/01*10262*00 We didn't want to make just another accessory controller, we wanted to make a smarter one. Harness the power and intelligence of your vehicle's CANbus electrical system. The DENALI CANsmart Controller provides plug-n-play installation of up to four accessories to enable dozens of customizable settings that can be controlled right from the BMW "WonderWheel" or the CANsmart Accessory Manager Software. The four dedicated circuits are pre-programmed to connect and independently control two sets of auxiliary lights, an auxiliary horn, and an auxiliary brake light. Each accessory circuit is electronically fused and ready to rock right out of the box. The two auxiliary light circuits enable independent adjustment of high and low beam brightness right from the vehicles "WonderWheel". It also features a "flash to pass" and "strobe when horn active" setting that will strobe the auxiliary lights when you pulse your high beam switch or sound your horn. The feature-rich brake light circuit will transform a simple 2-wire brake light into a "smart brake light" complete with running light, multiple flash pattern, and deceleration activated braking functionality. The horn circuit enables the addition of an auxiliary horn without having to add a relay and dedicated horn wiring harness. Simple Circuit Over-Ride Want more flexibility; we thought you might. You can set any of the four circuits to "Simple Circuit" Mode which will disable all custom circuit settings to provide a clean switched 12V circuit to power an accessory of your choice. Use this setting to power an alternative accessory in place of the dedicated DENALI accessory. The electronic fuse is the only active setting so you can properly fuse your accessory.

Easy and inexpensive Plug-N-Play wiring kit for Denali SoundBomb Air Horn that doesn't require any cutting, soldering, slicing or crimping. Clip one lead to your original horn trigger wire, one lead to battery ground, one lead to battery positive, and plug in your horn's relay.Please Note: A 5 Pin relay is not included with the DENDNL.ELC.10000 Plug-N-Play Wiring Kit. A Relay is provided with the purchase of a DENALI Soundbomb Compact and Split horn. If using the harness with another horn, please use this 5 Pin relay.“KTM motorcycles with CAN-BUS electrical systems (1090/1190/1290 Series) will require that the Original Equipment horn be retained and the DENDNL.ELC.10000 Plug-N-Play Wiring Kit be connected in parallel with the original horn wires”

Denali SoundBOMB Mini 113dB Horn (DENTT-SB.10200.B) Producing an massive 113 decibels of sound, the SoundBomb is over twice as loud as a standard motorcycle horn! The Denali™ SoundBomb was designed for those who want to be heard, but still want to maintain a stylish look. Thanks to its compact design and blacked-out housing, the SoundBomb will practically disappear once installed. At 113 decibels, the distinct low-tone sound from the DENALI SoundBomb Mini is overtwice as loud as a typical 100 decibel disc horn. Designed to be a direct Plug & Play upgrade from your factory horn, requiring no additional relay or wiring harness. When stock isn't quite enough, be heard with the SoundBomb Mini.Compatible with all CANbus electrical systems. Specifications: Sound Output: 113 dB at 3 feet Current Draw: 5 Amp Dimensions: 3.25"(82mm) x 3.4"(86mm) x 2.5"(63mm) Stylish All Black Design CANbus compatible Included: Single Piece Electromagnetic Horn Fully illustrated installation instructionsPlease note - Certain newer BMWs have a single horn connector and require an additional connector. Please see product code DENDNL.WHS.10100 in our shop.

At over 15,000 lumens, the DENALI D7 light kit is one of the brightest LED lights under 4.5 inches period. A pair of D7s feature 14 high-intensity, 10-watt LEDs that are focused through a proprietary single-piece optic specifically engineered to create a full bodied spot beam that can reach over 1500ft at an intensity of 1.0 lux. A pair of D7s will outshine 14 D2 lights and produces more than twice the light output of the D4. Not only are the new D7s incredibly bright, but they're strong, too. The robust heatsink and Active Thermal Management work together to keep this high-powered lamp cool enough to maintain maximum light output when you need it most. Because the new D7 has so much power, there's no need for a selection of optics. The standard optic set benefits from the raw power of this array to have best-in-class spot coverage at a distance, perfect for picking out wildlife way beyond the range of your motorcycle's normal high beam. With lumens to spare, the D7's optics were designed to preserve a near-flood-beam pattern, resulting in an amazingly wide (200ft) beam that helps illuminate the sides of the road. In a way, the combination of incredible intensity and optics that are neither too distance-focused or flood-oriented is the best of both worlds. In other ways, the D7 lights follow DENALI's reputation for innovative features. The D7 features DENALI’s DataDim™ Technology, which enables the lights to be upgraded in seconds to dual intensity by connecting a plug-n-play DataDim™ Controller that will automatically switch the lights between half and full intensity with your vehicle's original high beam switch. E-Mark Approval Number: E9*112R01/08*22253*00Features: Comprehensive LED light kit specifically designed for powersports applications High-Intensity Series Cree LEDs outputting 2190 lumens per kit DataDim™ equipped light pods and harness allow plug-n-play connection to the DataDim™ dimming controller Premium powersports harness with waterproof switch and handlebar switch mount included Plug-and-play installation. No wire cutting or splicing required. DrySeal™ Submersible Waterproof light and switch housings can withstand the most extreme environments Impact PC™ Polycarbonate bezels won't crack, fade or corrode like traditional aluminum bezels. LiveActive™ Thermal Management keeps the LEDs cool preventing the loss of light output from overheating Low profile mounting bracket with stainless-steel hardware included Specifications: LEDs: (14) 10 Watt Cree XPL HI Power Draw: 10 Amps Beam Distance: 1505ft Beam Width: 200ft Raw Lumens: 15330 Intensity: Single Intensity Harness DataDim™ Compatible: Yes Operating Voltage: 12 VDC Pod Size: 4.4in Round x 3.9in Deep IP67 Waterproof & Submersible E Mark Approved Spot LensesWhat's in the Box? (2) LED Light Pods (1) HotSwap™ Single Intensity Wiring Harness (1) DrySeal Waterproof Illuminated Switch (1) 7/8in Handlebar Switch Mount (1) 1.0in Handlebar Switch Mount (2) Hinge Mounts with M8 Stainless Steel Hardware (4) Zip Ties & (1) Adhesive Mounting Square

The DENALI horn mount for the BMW R1200GS LC '15-'18 & R1200GS Adventure '14-19, R1250GS / R1250GSA '19- is a bike-specific mounting kit for installing Denali SoundBomb Compact Dual-Tone Air Horn. All mounting hardware and instructions included. For easy wiring, check out the Plug-n-Play wiring kit. Use this slick horn mount for the cleanest looking installation possible!

DENALI 2.0 DataDim Dual-Intensity Controller (DENDNL.WHS.11000) This DENALI DataDim Dual-Intensity Controller enables the DENALI lights to switch between half and full intensity with your vehicle's original high beam switch. All DENALI 2.0 Light pods are equipped with a dedicated 3rd-wire dimming circuit so we can use an external signal to reliably control the intensity of the LED chip at the source.What's In The Box? (x1) DataDim Dual-Intensity Controller (x1) Dual-Intensity Trigger Wire

Denali SoundBOMB 120dB Horn (DENTT-SB.10000.B) Producing an earsplitting 120 decibels of sound, the SoundBomb is four times louder than a standard motorcycle horn! The Denali™ SoundBomb was designed for those who want to be heard, but still want to maintain a stylish look. Thanks to its compact design and blacked-out housing, the SoundBomb will practically disappear once installed. The unique design of the Denali compact horn features a rugged molded clamp that mechanically mates the compressor to the acoustic unit. This makes the SoundBomb virtually indestructible even in high vibration applications.Compatible with all CANbus electrical systems. Specifications: Sound Output: 120 dB at 3 feet Current Draw: 20 Amp Dimensions: 5.4” (137mm) wide x 4.5” (116mm) high x 3.6” (86 mm) deep Stylish All Black Design CANbus compatible Included: Single Piece Electro-Pneumatic Horn 12 volt, 30 amp relayPlease note - Certain newer BMWs have a single horn connector and require an additional connector. Please see product code DENDNL.WHS.10100 in our shop.

The DENALI auxiliary light mount for Honda Africa Twin CRF1000L provides a secure mounting solution for fitment of aftermarket lighting. Robust steel bracketry is laser cut for a precise fit and finished in a durable black powder coating. This versatile light mount is compatible with DENALI DM, D2, DX, D4 and DR1 LED light kits as well as most other popular brands of aftermarket lights. Existing bolt holes on the fairing stay are utilized without the need to drill, cut, weld or modify any components. The low profile design positions the lights close to the fairing for maximum visibility while also minimizing the risk of damage during a tip over or fall. Designed and engineered in the USA. Add the DENALI auxiliary light mount on your Africa Twin and enjoy the cleanest looking, easy to install & durable foundation for supporting your favourite Denali lights! Features: Robust laser cut steel construction Attractive & durable powder coated finish Bolt on installation does not require drilling, cutting or other modifications Utilizes existing fairing stay mounting locations for fitment Allows fitment of any DENALI DM, D2, DX, D4 & DR1 LED light kit Compatible with most brands of auxiliary lights M8 sized light mounting hole Provides a very clean & factory looking installation Low profile design positions the lights close to the fairing to minimize damage in a tip over or fall Proudly designed & engineered in the USA Two piece mount makes installation simpleWhat's in the box: DENALI auxiliary light mount for Honda Africa Twin CRF1000L (left & right side brackets) Mounting hardware Installation instructionsPlease Note: No lights are included with this kit, Mounting Bracket ONLY. Denali Lights available separately.

This Denali Mount Kits allow you to mount any Denali lights on your BMW R 1200 GS Adventure 2014- with ease, the laser-cut mild steel powder coated black bracket is both strong and attractive. This kit allows fitment of any Denali LED Lights.What's in the Box: Denali Lighting LED mounting bracket Installation instructions Mounting HardwarePlease Note: No lights are included with this kit, Mounting Bracket ONLY. Denali Lights available separately.

Denali BMW OEM Harness Adapter for Denali SoundBomb Horn (DENDNL.WHS.10100) Use the DENALI wiring adapter for connecting SoundBomb horns to the OEM BMW harness for a true plug & play connection. No wire tapping or other modifications to the original harness are necessary, just plug directly into the factory connector to send triggered power from your motorcycle. This handy little adapter is all you need when connecting a SoundBomb Mini to your BMW! For the original Compact SoundBomb and Split horn version, this special connector can be used to send triggered power from the harness so your factory horn button can activate your powerful new horn!. (The plug n play wire harness is still recommended to power both the Compact and Split models).Features: Enables true plug & play connection Plugs directly into OEM BMW horn connector No need to modify factory wiring No other wiring needed for SoundBomb Mini Functions as trigger for SoundBomb Compact Horn and SoundBomb Split Horn Simple & easy to install

This Denali Mount Kits allow you to mount the any Denali lights under its Headlight. Laser-cut from mild steel and powder coated black, this light mounting bracket is both strong and attractive. This specific light mount for the BMW R1200GS LC '13-. This kit allows fitment of any Denali LED Lights. Please Note: No lights are included with this kit, Mounting Bracket ONLY. Denali Lights available separately.What's in the Box: Denali Lighting LED mounting bracket, Installation instructions, Mounting HardwarePlease Note: No lights are included with this kit, Mounting Bracket ONLY. Denali Lights available separately.

Denali 2.0 Light Kits are brighter, more robust, and a lot more versatile. The all new Cree High-Intensity 10 watt LED's are focused through our TriOptic Lens System to give you three unique beam patterns in one kit. Equipped with DataDim Technology and a modular HotSwap wiring harness, the lights can be upgraded in seconds to switch between half and full intensity with your vehicle's original high beam switch. Our DrySeal submersible waterproof construction and Impact PC Bezels create super durable light and switch housings that can withstand the most extreme environments without giving up.DENALI 2.0 Features HiDrive High-Intensity Cree LED's TriOptic Multi-Beam Lens System DataDim LED Dimming Technology HotSwap Modular Wiring Harness System DrySeal Submersible Waterproof Illuminated Switch DrySeal Submersible Waterproof Light Housings Impact PC Corrosion-Proof Bezels LiveActive Intelligent Thermal Management Chrome Plated Optic Holders Low-Profile Mount with Stainless Steel Hardware Handlebar Switch Mounts Included E Mark Lenses Included Features Explained: HiDrive High-Intensity 10 Watt LED's: 2.0 lights feature the latest development from Cree; a new Hi-Intensity LED chip that features a redesigned primary optic to maximize light output through secondary optics. The 2.0 series LEDs are more efficient; producing more lumens and 15% more light output without increasing power draw. TriOptic Multi-Beam Lens System: 2.0 Light kits include two spot lenses and two elliptical flood lenses giving you three unique beam patterns in one kit. Use two spots for maximum distance, two elliptical floods for maximum spread, or one of each for the best of both worlds. Data Dim LED Dimming Technology: All 2.0 light pods are equipped with a dedicated 3rd-wire dimming circuit so we can use an external signal to reliably control the intensity of the LED chip at the source. Plug in our DataDim Controller (sold separately) to enable the DENALI lights to switch between half and full intensity with your vehicle's original high beam switch. Data-Dimming eliminates unnecessary modulation of the entire circuit which is unavoidable using basic two-wire dimming. HotSwap Modular Wiring Harness System: Our premium wiring harness features high-quality waterproof components and our clever HotSwap design that enables an effortless swap from the standard single-intensity relay to our dual-intensity DataDim controller (sold separately). DrySeal Submersible Waterproof Illuminated Switch: Our beefy, completely sealed, waterproof switch was engineered from the ground up to withstand harsh out-door abuse on powersports vehicles. It's clever design can be either flush or bar mounted. DrySeal Submersible Waterproof Light Housings: In addition to molded silicone gasket seals, we use a unique DrySeal construction technique that encases the wires in a potted cavity as they enter the housing. This ensures our housings are 100% watertight even when submerged underwater with the wires cut and connector removed. Impact PC Corrosion-Proof Bezels: Our Impact PC bezels are molded in 100% polycarbonate to create an impenetrable surface that won't rust, fade, or corrode even after taking repeated impacts from rocks and debris. LiveActive Intelligent Thermal Management: DENALI 2.0 lights feature cutting edge LED drivers that work with our uncompromising heatsinks to manage heat levels in real time. This duo works together to ensure that our lights stay cool enough to maintain the maximum light output when you need it most. Chrome Plated Optic Holders: We take the extra step to chrome plate our optic holders to maximize reflectivity and refine the appearance match the original chrome reflectors of your vehicle headlights. Low-Profile Mount with Stainless Steel Hardware: DENALI 2.0 light pods include a robust, low-profile hinge mount and stainless steel M8 mounting hardware. The low-profile hinge creates a super clean installation while maintaining maximum strength. Handlebar Switch Mount Included: Our versatile switch design can be either flush, perch, or bar mounted to your vehicle. DENALI 2.0 light kits include a handlebar mount to provide an integrated mounting location for the light switch right out of the box. E Mark Approved Lenses DENALI 2.0 kits include E Mark approved lenses D2 Kit Product Specs: LED's: (2x) 10 Watt Cree XPL HI Power Draw: 1.6 Amps Beam Distance (Spot): 525 Feet Beam Width (Spot): 75 Feet Raw Lumens: 2190 Intensity: Single Intensity Harness DataDim Compatible: Yes Operating Voltage: 12 VDC Pod Size: 2.2" Round x 2.4" Deep E-Mark Approval Number: AR-E9-00.16143D2 Kit Contents (2x) LED Light Pods (2x) Spot Lenses (Installed) (2x) E Mark Approved Elliptical Flood Lenses (Included) (1x) HotSwap Single Intensity Wiring Harness (1x) DrySeal Waterproof Illuminated Switch (1x) 7/8" inch Handlebar Switch Mount (1x) 1 inch Handlebar Switch Mount (2x) Hinge Mounts with M8 Stainless Steel Hardware (4x) Zip Ties & (1x) Adhesive Mounting Square

Denali Crashbar Light Mounts (Fits crashbars 21mm-29mm in diameter) These stylish clamps are machined from 6061-T6 Aluminum for strength and durability. The kit allows fitment of any Denali LED Lighting Kit to any tubular bar ranging from 21mm to 29mm in diameter. The bracket can be mounted in numerous positions allowing the light pods to be placed for optimal beam projection, while keeping the pods themselves protected.Kit Includes: 2x black anodized aluminum machined clamp Mounting HardwareCompatible with ALL Denali lights.